Thursday, March 9, 2017

configure ipx on cisco router

***r1 configuration ***
ipx routing
!
interface FastEthernet0/0
 description *** Unused for Layer2 SW ***
 no ip address
 duplex auto
 speed auto
 ipx network 100



***r2 configuration
ipx routing c402.350b.0000
!
interface FastEthernet0/0
 description *** Unused for Layer2 SW ***
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 ipx network 100
!
interface FastEthernet0/1
 description *** Unused for Layer2 SW ***
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 ipx network 200



***r3 configuration ********

ipx routing c403.350b.0000
!
interface FastEthernet0/0
 description *** Unused for Layer2 SW ***
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 ipx network 200
!
interface FastEthernet0/1
 description *** Unused for Layer2 SW ***
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 ipx network 300



1- show ipx routing table
R1-SW#show ipx route
Codes: C - Connected primary network,    c - Connected secondary network
       S - Static, F - Floating static, L - Local (internal), W - IPXWAN
       R - RIP, E - EIGRP, X - External, A - Aggregate
       s - seconds, u - uses, U - Per-user static/Unknown, H - Hold-down

3 Total IPX routes. Up to 1 parallel paths and 16 hops allowed.

No default route known.

C        100 (NOVELL-ETHER),  Fa0/0
R        200 [02/01] via      100.c402.350b.0000,   47s, Fa0/0
R        300 [03/02] via      100.c402.350b.0000,   47s, Fa0/0


2- show ipx interface
R1-SW#show ipx interface
FastEthernet0/0 is up, line protocol is up
  IPX address is 100.c400.350b.0000, NOVELL-ETHER [up]
  Delay of this IPX network, in ticks is 1
  IPXWAN processing not enabled on this interface.
  IPX SAP update interval is 60 seconds
  IPX type 20 propagation packet forwarding is disabled
  Incoming access list is not set
  Outgoing access list is not set
  IPX helper access list is not set
  SAP GGS output filter list is not set
  SAP GNS processing enabled, delay 0 ms, output filter list is not set
  SAP Input filter list is not set
  SAP Output filter list is not set
  SAP Router filter list is not set
  Input filter list is not set
  Output filter list is not set
  Router filter list is not set
  Netbios Input host access list is not set
  Netbios Input bytes access list is not set
  Netbios Output host access list is not set
  Netbios Output bytes access list is not set
  Updates each 60 seconds aging multiples RIP: 3 SAP: 3
  SAP interpacket delay is 55 ms, maximum size is 480 bytes
  RIP interpacket delay is 55 ms, maximum size is 432 bytes
  RIP response delay is not set
  IPX accounting is disabled
  IPX fast switching is configured (enabled)
  RIP packets received 18, RIP packets sent 1, 0 Throttled
  RIP specific requests received 0, RIP specific replies sent 0
  RIP general requests received 1, 0 ignored, RIP general replies sent 0
  SAP packets received 1, SAP packets sent 1, 0 Throttled
  SAP GNS packets received 0, SAP GNS replies sent 0
  SAP GGS packets received 1, 0 ignored, SAP GGS replies sent 0
 


3- ping to remote ipx address
 R1-SW#ping 300.c404.350b.0000

Type escape sequence to abort.
Sending 5, 100-byte IPX Novell Echoes to 300.c404.350b.0000, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 44/63/80 ms






No comments:

Post a Comment